How to install shower wall panels?

by delavin home June 30, 2024

Sources

Waterproofing Tub Shower Walls | Easiest Method for Beginners

www.youtube.com

Build.com For Pros: How to Install a Shower Panel

www.build.com

How to Install Shower Panels | The Panel Company - YouTube

www.youtube.com

How to Prepare Your Walls for Shower Panels | Tapron UK

tapron.co.uk

Answer

Here are the key steps to install shower wall panels:

Prepare the Wall Surface

Ensure the wall surface is clean, dry, and free of any debris or protrusions
1
4.
If installing over existing tiles, make sure they are well-adhered and fill any gaps or uneven areas with a suitable filler4.

Cut the Panels to Size

Measure the wall area and cut the panels to size using a fine-tooth saw and miter block for clean edges
3
.

Apply Adhesive

Apply a bead of silicone adhesive to the back of the panel or directly onto the wall
1
4.

Install the First Panel

Hold the first panel in place and press firmly to secure
1
3
.
Use a level to ensure the panel is straight
1
2.

Install Subsequent Panels

Apply silicone to the edge of the installed panel
3
.
Slot the next panel into place, pressing firmly
3
.
Wipe away any excess silicone immediately with a damp cloth
3
.

Seal the Edges

Apply silicone sealant around the top and sides of the installed panels
1
2.
Avoid sealing the bottom to allow water to escape if needed2.

Install Trims and Finishing Touches

Measure and cut any trims or edging pieces to size using a miter block
3
.
Apply silicone to the back and press into place
3
.
Remove any protective films once fully installed
3
.

Take your time and ensure a watertight seal for a successful shower panel installation. With the right preparation and adhesive, shower panels offer a quick and easy alternative to traditional tiling.

References

1. Waterproofing Tub Shower Walls | Easiest Method for Beginners 2. Build.com For Pros: How to Install a Shower Panel 3. How to Install Shower Panels | The Panel Company - YouTube 4. How to Prepare Your Walls for Shower Panels | Tapron UK 5. Bathroom Partition Installation

BpeARATAdHw

Author: The Panel Company

Key insights

The clad seal strip ensures a watertight seal around a bath or shower tray, making the installation process practical and low maintenance.
Using a miter block and fine-tooth hand saw is essential for achieving a flush finish when cutting the clad seal trim for the shower panels.
️ The use of silicon and internal corner trims is essential for a successful installation of shower panels.
️ Using a fine-tooth saw to cut panels is an alternative method, but it's important to have a sharp saw to prevent damage to the panel.
Applying extra adhesive to compensate for uneven walls can ensure proper adhesion of the shower panels.
To make the panels watertight, run a bead of silicon into the groove of the first panel before slotting the next one in.
The use of silicon and protective film is essential for a successful installation of shower panels.
The availability of different colors and styles provides plenty of options for customization.

Timestamped Summary

00:00 Install shower panels by starting from the ground up and using clad seal strips for a watertight finish.
00:43 Measure and cut the clad seal trim, then permanently install it with silicon for a water-tight finish.
01:36 Install end caps, measure and cut internal corner trim, apply silicon, and remove protective film before fitting wall panels.
03:53 Cut and install wall panels using a stanley knife or fine-tooth saw, making sure to measure and score before snapping or sawing.
05:32 Install shower panels by measuring, cutting, applying adhesive in a zigzag pattern, and using a staple gun for plasterboard.
07:15 Install shower panels by using screws or staples, applying silicon to make it watertight, and removing any excess silicon with a damp cloth.
08:03 Install shower panels by measuring, cutting, and applying finishing trims.
09:13 Installing shower panels is easy with basic DIY tools, and there are plenty of colors and styles available to choose from.

Video Full Text

00:00 Hello it's james from the panel company. Here. Today. We're going to be talking about the installation of these shower panels that you see behind me. Now these panels could not be easy to fit. They offer a practical yet stylish low maintenance finish. Let's get to it to begin with you want to work from the ground up. The clad seal strip ensures a watertight seal around a bath or shower tray. We also recommend clad seal end caps which are attached to the end of the clad seal strip. This will ensure that no silicon is exposed on top of the shower tray is where the clad seal strip is installed. You will also use the clad seal strip if you are fitting around the bath to begin installing your clad seal strip.
Read More
00:43 You will first need to measure from the corner of the shower tray to the end on the two sides that are against the wall using a fine tooth. Handsaw you can now cut the clad seal trim to size on the two ends of the clad seal strip which will meet in the corner of the shower. Tray use a fine-tooth hand saw and a miter block to ensure a flush finish. Now that we've test fitted the clad seal strips. We can now permanently install it by running a line of silicon on the underside level off the silicon using a spatula. The spatula can be found on the optional end caps before installing the clad seal strip. You'll also want to run a bead of silicon along the surface of the shower tray and along the surface of the wall. This is to ensure that the bead of silicon on the shower tray bonds with the silicon that we placed along the strip to create a water-tight finish once installed wipe away.
Read More
01:36 Any excess silicon install the end caps by pushing them into place before we fit the wall panels. We need to install the one piece internal corner trim to do this we're going to measure from where the panel will sit on the clad seal strip to the ceiling and then cut the internal corner to the correct length. Using a fine-tooth saw. We can now permanently install it by running a line of silicon on the underside when installing the internal corner apply pressure to the top and bottom to ensure a good bond with the surface of the wall. Once installed you can now remove any protective film from the trim using the same measurements that we used to fit the internal corner.
Read More
03:53 We are going to cut and install the wall panels. In this video. We are going to show two different methods in which you can cut your wall panel. The first method we are going to use is with a stanley knife flip the panel so the design side is facing upwards using the measurements from earlier measure out. The length of the panel add a mark at the correct measurement and then using a ruler or spare piece of trim draw. A straight line across the panel install a new blade into the stanley knife and score across the line. We drew earlier repeat this step. A few times once scored apply moderate pressure to the end of the panel to snap it off. The next method for cutting. The panels is to use a fine-tooth saw like we used to cut the trims we only recommend this option if you have a sharp fine-tooth saw to prevent damaging the bottom of the panel.
Read More
05:32 This time place the panel with the design facing down again using the measurements from earlier measure out the panel and leave a mark at the correct measurement using a ruler or spare piece of trim draw. A straight line across the panel using the hand saw cut along the straight line. We are now going to go on to the installation of the wall. Panels. Themselves apply a generous amount of adhesive to the reverse side of the panel in a zigzag pattern. If some areas of your wall are uneven use extra adhesive to compensate for this apply pressure to the top middle and bottom of the panel to ensure it adheres correctly to the wall if you are using plasterboard. You can use a staple gun to staple the tongue of the first panel to ensure it doesn't move while the adhesive sets.
Read More
07:15 You can also use a screw to do this but just ensure you don't damage the face of the panel. If you have used this method ensure any staples or screws are flush with the tongue so it doesn't catch on the next panel when you install it. It's now time to install the second panel first run a bead of silicon into the groove of the first panel before slotting the next one in to make it watertight. If any silicon seeps out of the face of the panel remove it immediately with a damp cloth. If you have a tiled surface. Then the panels can be installed directly over the tiles using silicon once installed if your panel has a protective film you can remove this now you can now repeat this process for the remainder of the wall.
Read More
08:03 For this installation design we have used two different panels from the same collection. We will leave a link in the description where you can buy these panels. Now that the panels have been installed. You are now ready to install the finishing trims to begin installing the quadrant trim. We first need to measure the area shown in the video. Once we have the measurements we can now cut the trim where the trim will be meeting in the corner use a miter block to cut the correct angle again as done previously test fit the trim to ensure it fits and then apply a bead of silicon to the underside and push it into place. You can now remove any protective film that was on the front of the trim right.
Read More
09:13 So it really is that easy to get a finish like like this behind us now remember. I've only used basic diy tools that anybody will have at home. I've not used any power tools here so it really is quite straightforward to fit now remember guys. We do have plenty of different colors available and different styles. If you've got any questions. Please give us a call or log on to palcompany.com find us on facebook or on youtube thanks a lot guys.
Read More