How to install frameless shower door?
Sources
How to Install a Frameless Shower Door - Colorado Glass and Mirror
mycoloradoglass.com
·
1
Original Frameless Shower Door Installation Video: Watch It DYI
www.framelessshowerdoors.com
·
2
How to Install a Semi Frameless Glass Shower Door - YouTube
www.youtube.com
·
3
[PDF] Installation Instructions - Sliding Shower Door - Kohler
resources.kohler.com
·
4
Answer
Here are the key steps to install a frameless shower door:
Prepare the Shower Opening
- Clean the shower area, removing all dirt, soap buildup, and old caulk or glue1
- Check walls and floor for any cracks, breaks or uneven surfaces that need repairing1
- Measure the shower opening accurately to select the right size frameless door1
Attach Hinges or Rollers
- Refer to the manufacturer's guide for proper placement of hinges or rollers14
- Use a level to ensure hinges/rollers are aligned correctly1
- Firmly screw in the hinges or rollers to support the shower door panels14
Hang the Shower Door Panels
- Carefully lift each panel, ensuring they are level and straight1
- Adjust as needed to achieve proper alignment1
- Securely attach each panel to its corresponding hinge or roller14
Add Final Touches
- Install handles and ensure they are properly aligned and tight1
- Caulk any gaps between the door and wall with silicone sealant4
- Clean the glass with a gentle cleaner and inspect for any damage1
References
1. How to Install a Frameless Shower Door - Colorado Glass and Mirror2. Original Frameless Shower Door Installation Video: Watch It DYI3. How to Install a Semi Frameless Glass Shower Door - YouTube4. [PDF] Installation Instructions - Sliding Shower Door - Kohler5. how to install a frameless shower glass door - YouTube
Author: TileCoach
Key insights
- It's important to ensure that the walls are nice and flat before measuring and ordering the glass for the shower doors to make installation easier.
- ️ Using a mortar bed instead of foam on the floor creates a nice, seamless look for the shower.
- Using the right drill bits is crucial for drilling through porcelain tiles without damaging the waterproofing.
- Cutting the screws and anchors to avoid puncturing the waterproofing during installation is a smart and practical tip.
- Solid backing is crucial for support when installing a frameless shower door, especially on the hinge side.
- It's important to measure and mark the top of the panel for accurate installation of the door hinges.
- ️ The process of installing a frameless shower door involves adjusting the doors and panels to ensure the right fit and gap size.
- Using denatured alcohol to clean the joints before installation can ensure a good finish.
Video Full Text
- On today's episode on the same concept they have the side without the fastener. Then they have the side where the bolts go in okay. So these are the door handles all right hey so we're gonna be installing some shower doors. Today these are 3/8 frameless glass and it creates a real nice seamless look. It's. It's a really good way to go so you don't have the track and the header to go around it. It's just solid glass panels so the first thing we had to do was measure. This so you got to make sure your walls are nice and flat that makes it a lot easier because you don't have any track to hide it on and we've been floating our wall. So if you come over here and you can see if I put my level on on here you can see. We have a nice plumb flat wall and that makes it real easy when you go to order the glass so basically what we're gonna have is. We're gonna have a solid panel that's just held in with four clips. Then we're gonna have a door on this side which will open both ways and that's that's got two hinges and that's all the hardware and we order the hardware to match. The plumbing finishes so we have polished nickel. So like these are the clips that hold the panel and I got my lines up. I drew plumb lines and straight lines so that I make sure everything is in the same plane so I just took a measurement of an inch and a half off of the edge of the curb.Read More
- That's gonna allow us enough meat to grab into on the tile. But I like to have the doors and the panels as far towards the outside of the showers I can get them that way you have a little more room and this is a really nice shower. We use three by twelve ceramic tile. It's a studio look kind of handmade. This is a tile from Spain ceramic. We used two dark grout to really kind of accent the tiles themselves polished nickel finishes and got a hand shower. We got a diverter and we got a showerhead which we're still waiting on but that's coming in we got. A we got a low-profile curb with a single sloped shower pan. We have looters tileable great here and so these guys are pretty. Slick. I can get this guy up so that's the actual drain and so we did. We did we do a mortar bed. I don't like to use foam on the floor. So this is all floated. Nice seamless look low profile curb. It goes down to and we only have about three eighths of an inch there and obviously it grows as the slope goes down.Read More
- That's enough about the tiles and it's also really good when you build your showers if you're doing frameless glass make sure your your level across your. Kirk we're right in the middle with that so makes everything a lot easier to measure these are cyclone. These are for going into or on the curb when I'm drilling for the curb I don't want to puncture all the way through my waterproofing. I'm basically just going to go through the tile and then I'm gonna cut my screw. So I don't puncture all the way through. But it's still going to hold that panel from going in or out. And we have Kirti waterproofing. So it's right underneath the tile so I'm going to be careful so I'm artery already through there. So that's as far as I want to you can feel it when it goes through it. It pops so I'm just through the tile I'm not through any waterproofing there. So that's into porcelain so these bits work really good and they're hot and when I touched it the first time I'm actually actually burnt my finger a little bit well. My fingertips are pretty calloused anyway so but I can feel it okay all right. So we vacuumed this up nice.Read More
- I'm going to pull my tape up. I said I don't want to puncture through. They give you these two inch stainless steel screws and if I were to sink this all the way down I'd be going right through my waterproofing again. I'm gonna cut these two about 3/8 of an inch so that they don't. I'm just going to use my dikes boom them and cut my screws down and then I got to cut my anchors down a little bit too. They're a lot easier to cut and then stainless steel screws so the hardware it's got two sides. It's got the attachment screws side and it's got the flat finish side. So there's two sides to these clips and they go together. I always put the finish side on the outside of my viewers comment on my Milwaukee impact bits. This is my Phillips bit let me know leave it in the comments below what's your favorite impact drill bit yeah. I've noticed the Milwaukee's. They get kind of worn down oh and actually I hit my thumb yesterday pretty bad cuz. It slipped out and jammed right into my thumb right there and it's kind of sore. But if you got a good bit hey let's share some information and and let me know what your favorite bit is yeah. Those are actually in there pretty tight. This you're getting a pop on your impact like that that means that means you're in there pretty good. So we got that you'll notice when I drilled I drilled all the way through this all the way through drywall.Read More
- I don't have solid backing under this which probably would have been a good idea. But since it's the panel and again it's not going to have any for the door side. I definitely want solid backing because that door is gonna be hanging and those two hinges all the support coming from the hinge side. That's where the load is resting this side. There's not going to be any vote on it glass in for the panel. I use these glass shims these little rubber guys and they they cushion so you put these down and when you set the glass on because you want to set them on something soft. If you set them right on the curb you're prone to chip make sure I'm gonna rest on those shims okay my all the way against the glass. There we go with the hardware they give you these little spacers. This is just a stainless steel with an allen key definitely need to people when you're doing this see I'll just get these snug for now okay trustees to build a level here to find out what's going on with this panel. Again you saw we just snugged everything so go ahead and up over here. Johnny then you can see we got. We're out of plumb. So I'm basically gonna have to lift up the bottom here and push the top corner thing about. If you do tile work. You can really take that into the other trades as well. Plumb level square so come check out the door now if you understand how to make things plumb. So I lift it up the bottom and push it in the top and now we're right way.Read More
- So these are the door handles. They're. They have a little set screws. I saw they come in a pack the door in. It's just another place that we can grab. That's the way that goes and this just screws on metal washer and I'll screw it in don't use your impact. For this part. You don't need to you got those rubber washers so you're just getting a good snug in here seeing it from the top part just goes on there that screw started alright. It's a glass okay so the door hinges are a little bit different than the clips. But they have kind of the same concept. They have the side without the fastener. Then they have the side where the bolts go in of course again. We want the side with the bolts to find out where these are gonna get screwed into it's really important. So I took after I get my panel in I take the top of it not the bottom because the bottom of the door actually has a sweep which I'll show you in a second and if you try to put that up there you can't gauge it. So I go off of the top so I measured off. The top took a level from here and made a mark right here. So that's my top and then to get my measurements of the hinges. I took my tape measure and measured from here and got my. There. You go okay. I'm on are you. He's kind of act. The same way here is. It's like doing it in a mirror oh.Read More
- Here's the outer hinge. We got the pant at the door. Wish. I could show you guys this. But we got the door in line on both hinges. So each side gets a rubber rubber gasket. Two allen screws and again our first go around. We're just going to get this snug because we're gonna have to adjust these doors to get them. Plumbing level just like we did the other ones push in a little more yeah. Back up just a little bit back up a little bit back up a little bit okay so we got you got our door on. Here. It's looking good everything's plumb but we have a little bit too big of a gap here. I'm looking for about 3/16 right here and it looks like we have more like quarter-inch maybe even 3/8. So we're gonna adjust these doors to the door to bring it this way. If we have to we'll adjust the panel and bring it in okay. So we got our you can see. We got our gap closed - you're real nice so the door opens both ways right there. It's all plumb and level and no tracks or anything to deal with. It's just just really good shape really good solid door. So last thing we need to do is just silicone right here and we're all good okay so last thing. We do is silicone in the panel. We don't need to do the door so I'm just using 100% silicone fill in the gap real.Read More
- Nice I use denatured alcohol to give it a give it a good joint you guys do this to alcohol yeah. This is the finished product. It's a really nice glass door so again thanks for checking out my videos and be sure to watch the next video coming up it'll be. Just like this one you'll get a lot of info out of it. I think you'll enjoy it click like and subscribe. We'll see you next video thanks guys.Read More