Can you put a shower door on a bathtub?

Sources

Shower Door Bathtub Install - Do It Yourself - YouTube

youtube

·

1

Let's Install a Glass Shower Door - YouTube

youtube

·

2

Choosing a Shower Door - Framed or Frameless?

videos.homedepot

·

3

Answer

Yes, you can install a shower door on a bathtub. It is a common home improvement project that can be done as a DIY task or by hiring a professional.

1

2

Steps to Install a Shower Door on a Bathtub

1. Measure the Opening: Measure the distance between the walls where the shower door will be installed. This measurement will determine the size of the shower door kit you need to purchase.
2. Purchase a Shower Door Kit: Buy a shower door kit designed specifically for bathtubs. These kits come with all the necessary components like the glass panels, metal frame, and hardware.
3. Prepare the Area: Remove the existing shower curtain rod and any other obstructions. Ensure the tub is level and the walls are plumb (vertical).
4. Install the Track: Install the bottom track along the tub's edge, ensuring it is level. The high side of the track should face outwards to prevent water from spilling onto the floor.
5. Install Wall Channels: Install the wall channels on both sides, ensuring they are plumb. These channels will hold the glass panels in place.
6. Install Glass Panels: Carefully insert the glass panels into the wall channels and bottom track, following the manufacturer's instructions.
7. Seal and Caulk: Apply silicone sealant along the edges of the shower door frame to prevent water leakage.

Benefits of Installing a Shower Door

• Improves bathroom aesthetics and increases home value.
• Easier to clean and maintain than shower curtains.
• Prevents water from spilling onto the bathroom floor.
• Provides a more spacious and open feel to the bathroom.

It's important to follow the manufacturer's instructions carefully and take proper safety precautions when handling glass panels. If you're unsure about the installation process, it's recommended to hire a professional.

1

2

Video Full Text

• 00:00 How many times has this happened to you either you or someone in your family. Doesn't quite get the shower curtain into the tub properly and you're stuck with a watery mess. Not only is this frustrating it can damage your floor and that can lead to some really big problems. But you can put an end to your problems and give your bathroom a fresh new look by installing a glass shower door. Best of all you can do it. Yourself getting rid of your curtain. Rod is fairly simple this one's adjustable and fits to the wall others you just have to remove a few screws. What we're going to do. Today is install a metal frame along the tub edge and the walls where the shower curtain used to be. The panels are made of tempered glass which means they'll shatter safely without sharp edges. If the glass should ever break. Many different manufacturers make shower door kits and you can get them at your local hardware store or home center.

  Read More
• 00:59 The first thing that you need to do is make sure that your tub is level and also that the walls are plumb and these look fine but if you're off level by more than a quarter of an inch you'll need to make some adjustments go to your local home center and get some shim stock. Like these these are small metal pieces that can be placed underneath the track in the area where you need it to be level and that will solve your problem. Now what you do next is measure the wall to wall distance in the center of the tub ledge because this is where your track is going to sit minus 57 and a half now according to the instructions in your kit. You'll need to subtract just a fraction of an inch from that measurement to allow for the wall channel to sit behind the track. This is the measurement you'll use to cut your track you'll need a hacksaw to make your cut so measure and mark the track where it needs to be cut which is here and then use a square so that you have a straight line to follow and remember you should always wear safety. Goggles too now you're ready to put your track down make sure that you put the high side of the track which is this side towards the outside that way it'll keep the water from spilling out from the tub onto your floor.

  Read More
• 02:37 I'm going to use this wall channel and put that in place and now I know I have enough room at each end for the channels to fit to be on the safe side. I'm going to tape that down. So it doesn't fall on me now line this up and center it and then again use the masking tape to tape that down and hold it in place so that you can mark where the track is going mark that all the way down okay now use the level on your wall channel to make your adjustments to put that where it needs to be and then use your pencil and mark the three holes where you'll be drilling okay.

  Read More
• 03:20 We get rid of this because now we're ready to drill. I'm using a hammer drill and a masonry bit to drill through the tile but first to protect your tile. You can use your masking tape to make an x over the mark you'll still be able to see it. But what this is for is to keep your drill bit from walking or moving around on the tile now just to be on the safe side. Anytime you're drilling into the wall if you're unsure whether or not there's electrical wires just turn off the power for that area that you're working now. After you're finished drilling you need to install wall anchors in each of the holes so get rid of your tape and then take your hammer to hammer. These in before you install.

  Read More
• 04:26 The track make sure that you clean the ledge of the tub thoroughly so that your sealant will adhere properly after that's clean turn the track over and apply a thick continuous bead of sealant all the way down the track. Now the sealants come in a few different shades so you should be able to pick one to match the color of your tub again make sure that you put the high side facing the outside of the tub line. This up with your mark and then push this down into place and if you see some sealing coming out from underneath that's okay because that's letting you know you're going to have a good seal and you can clean that up later after you've applied sealant to the back of your wall channel slip. This down behind the track and then push it up the wall to your wall anchors.

  Read More
• 05:30 Most kits will come with rubber bumpers. These need to be added to the anchor screw for the top and the bottom screw for. Each channel then put this into your wall anchor and screw it in all right. That was the last screw for the other wall channel before I move on this will be a good time to clean up all that excess sealant you can take a paper towel to wipe away most of it and then use a damp sponge to finish cleaning it up and you can just do this all the way around your frame to clean everything up before we install the top bar which is called the header again I'm going to measure wall to wall and that's only because your walls may vary just slightly. This is just a hair over 57 and a half you want to have the exact measurement so that you have a good tight fit. Let's go cut it now all you have to do is slip. The header down over the wall channels and your frame is all set.

  Read More
• 06:40 We just have a couple more steps to go and we're finished for the door panels. You need to install two of the rollers on each door and I'm installing these on the second hole from the top. The other holes are there just in case you need to make any adjustments so tighten your screw up and I've got a small piece of track to show you how this works. When you install. The door put the roller up in the channel like that and that's how it works. All right now just take your panel and put it up into the header and set those rollers down into the channel see how nice that works. I've already installed the rollers on the outside door. So let's put this one in again put this up into the header with the roller sitting down on the channels. Now if you'll notice this door has a bottom piece that sits right on the high side of the track. So see this one works nicely as well.

  Read More
• 07:45 But let's put it to the test. As you can see. The doors are doing a great job plus. We've just added a brand new look to this bathroom now for the average do-it-yourselfer. This will probably take you between two to three hours to complete the installation. Then the only water you have to worry about is from you when you step out of the shower you.

  Read More